VU+ PC Tools & Editor Support DCC Help

DirtyDonki

I am the Nice One
Staff member
Admin
Joined
Sep 10, 2014
Messages
25,575
Points
728
Location
Middle England, Planet Earth.
Website
www.metalarmy.net
You are using wrong version of DCC. Version 1.41 works fine.
1.41 appears to work OK. All other versions above it appear to work until you change the password. Then, like all the other versions I've tried, it fails and can only be closed via Task Mangler. So exactly the same as 1.50 & 2.95 for me. The problem can be temporarily resolved by deleting the ini file and starting again. After doing that it closes as normal again until you try to set a different password. If you then revert back to using dreambox it works as expected again. So it appears this is being caused by a password change and it doesn't seem to matter what is used either.

....and with that as the only solution appears to be to use 1.41 :closed: :mutley:
 
Last edited:

skyroadjim

Vuplus-Images Elite
Member
Joined
Apr 4, 2016
Messages
15
Points
3
im having problems with the dcc programme lately with freezing and and not exiting off screen and failing to transfer files to vu box im using dcc e2 never had problems before does anybody have these problems or is their a better ftp programme
 

Nutty

Member
Joined
Feb 5, 2016
Messages
9
Points
3
I have just downloaded version 2.96 and after a minute or two it keeps freezing - I cant even close it down without switching the lap top off. The IP addresses are all correct and it seems to connect ok to the Solo2 fine but it does not to the router (I don't believe this is that important though). At the bottom it says FTP and telnet connected (green squares) but as I mentioned it just freezes and I can't do anything. In the protocol section there is nothing in there (I believe it should say Enigma 2 connected or something like that?). I suspect I have done something wrong somewhere but I was just wondering if this is a known problem. I am using Tens Open Vix back up 5.0-024 for the solo2.
 

majz

Significant Contributor
Vuplus-Images Elite
Joined
Oct 8, 2014
Messages
370
Points
43
Location
Somewhere in Wales
Try using a different image like openpli 6.2 and see if it works, I had the same problem with open vix and openatv but since using openpli no problems.
 

celbun

Member
Joined
Nov 26, 2016
Messages
39
Points
8
Sall, please a little help. I have an amiko mini 265 and I can not connect to dcc, it gives me error
root telnet password. not working.
 

DirtyDonki

I am the Nice One
Staff member
Admin
Joined
Sep 10, 2014
Messages
25,575
Points
728
Location
Middle England, Planet Earth.
Website
www.metalarmy.net
Amiko is not supported by us but if it is running Enigma2 then you should be able to use:
Username: root
Password: anything you like usually eg: dreambox, amiko, etc. Could also be the image team name eg: openspa
DCC does not normally work unless a password is set.

Try looking in some of the threads in this section for answers:
Problems with DCC & Windows 10
ftp settings
Login with no password
 

sparks1950

Member
Joined
Jan 28, 2018
Messages
5
Points
1
Location
malta
when I try to connect with Putty to my vu+zero I log in as ROOT and when i leave password blank it says incorrect login. when I try to write something in for password nothing is written in the box.
can anyone tell me why this is happening ? on my other vu+ zero box everything works fine.
I am using b/h 2.1.7.01 fw.
any help will be much appreciated
Thanks in advance for any help
 

Ten Below

Staff member
Admin
Joined
Sep 9, 2014
Messages
7,937
Points
528
Location
@vuplusimages
Website
vuplus-images.co.uk
when I try to connect with Putty to my vu+zero I log in as ROOT and when i leave password blank it says incorrect login. when I try to write something in for password nothing is written in the box.
can anyone tell me why this is happening ? on my other vu+ zero box everything works fine.
I am using b/h 2.1.7.01 fw.
any help will be much appreciated
Thanks in advance for any help
Which telnet client are you using?
Try with this....
VU+ Control Centre Latest Version
 

sparks1950

Member
Joined
Jan 28, 2018
Messages
5
Points
1
Location
malta
thanks TEN . I`ll try it as soon as soon as I am allowed to download it.
Btw I`m using putty , but any app I use gives me same result.
will let you know what happens. Thanks again

hi Ten. tried this app, but same result. what I am getting is what there is on image below.
tried doing factory reset but still same.
was thinking about upgrading to blackhole 3.0 from 2.1.7. but forgot how I did it on my other box.
can you please direct me to a thread that shows how to do it, if you think that it can help?
thanks a lot Ten for all your work here for all of us

hi Ten, problem solved by installing new firmware b/h 3.0.5 and everything worked out perfectly.
Thank you for all the work you and the others do for us here

:closed:
 

Attachments

Last edited by a moderator:

Similar threads


Top