Channel List Support duo 2 39 east bull sau

[deltec]

how come I can get bull sat with my technomate 5402 with my cline and I can not open the channels with my duo2 with my cline is there a way I can open 39 east bull sat with my duo 2 and cline if so could boday explain how I do this please thank u very much for all the help so far regards deltec great forum

 

[Ten Below]

The CCcam in the TM5402 is actually a patched version of mgcamd, to clear these in our duo2 use Mgcamd, Oscam, ymod or doscam as client.

 

[deltec]

thank u again :b0227:

 

[rumpole]

like yourself i have never found out how to add a c-line
on a mgcamd config file to get these channels open even
as you say a patched non linux box opens the channels and
if anyone can say which works and how to set it up that would
be very helpfull to me

 

[deltec]

could some one how u do the above please regards deltec

 

[Ten Below]

could some one how u do the above please regards deltec

In the mg_cfg the only lines you should need to change from the default values are these.

# network mode, use summ for several clients
# 00 no network (default)
# 01 newcamd netclient
# 02 radegast netclient
# 04 camd3 netclient
# 08 gbox netclient
# 32 cccamd netclient, card list saved as /tmp/cccamd.info
# (ECM only, supported server version up to 2.1.1, later not work)
G: { 32 }

# box type
# 00 autodetect, change only if you think wrong type detected.
# 01 dbox2
# 02 dreambox
# 03 triple-dragon
# 04 relook
# 05 openbox
# 06 dreambox/mips
# 08 stapi/kathrein
# 09 stapi/ipbox
# 11 stapi/openbox
B: { 06 }

Paste you sealion into the file cccamd.list if you find it is named cccamd.list.example then rename that file removing the .example from the end.

 

[deltec]

don't understand mate

 

[Ten Below]

don't understand mate

What image are you using deltec?

 

[deltec]

the latest black hole image

 

[Ten Below]

Ok install this is you don't already have mgcamd installed, once done you will find the files to edit in the /usr/keys/ directory.
View attachment mgcamd-1.3.8_blackhole2_all.ipk

 

[deltec]

still stuck with this

 

[Banny]

You connect to your Duo2 by FTP, browse to the folder - /usr/keys/ in that folder you should find a file called cccamd.list, open/edit it put in your peers sealions (**Sounds like**) details and save the file. You then need to go to your CAMS section make sure MGCAMD is active, it shouldn't require the cam or box to be restarted but you could for good measure, or if making this change doesnt trigger the channels you are referring to to clear.

-----
Im putting this on your post, but offer it advice to all members -

Id suggest building your self a set of reference sheets/files/folders of the steps you took to resolve issues or get new features working, this way should you change image to a new/different version in the future, also means you have the config files, addons and the information to hand and makes the task easier the second time round. With time and patience, all the jargon, terms and files you need to amend will be an easier task...

It worked for me, and if I can do it I am sure you can

 

[deltec]

ill give it a go

 

[deltec]

still stuck

 

[deltec]

whats sounds like mean mate

 

[deltec]

still having problems so I look in my dcc first

 

[Banny]

Its no good saying still stuck, what is your problem? What have you done to try to fix the problem? What happend?

If you provide us with information we may be able to help, but your not giving us much to go off. How did you manage to do this on your technomate?

The setup and configurations are practically the same. With all due respect, you have been asking how to do things, that if your intending to be a hobbyist, should not cause you a headache for long.

Short version - We need you to explain how far you have got, is this even your local or you using a motorised dish etc etc

 

[deltec]

never did it with my technomate resever is there a tutorial on it please ill start from scratch

 

[Banny]

http://vuplus-images.co.uk/index.php?threads/setting-up-openatv-for-s-y-and-Vermin.2603/

Try following this and changing the sat for the one you want, and is this your local, motorised or otherwise?

If you can't tell us your setup and issue, we can't answer you.
----

We are not going to write a step by step guide specific to your needs alone, these things take time, your response are one sentence at best. Everyone is making a massive effort to help, and understand your issues, but you need to help yourself too....

It also seems you are trying to many different things at once, set yourself a target get there, understand how you got there.... You can also find all the answers to transfer from your Technomate.
-----------------

The more you try to help yourself the more other forum members will endeavor to help you.

 

[deltec]

iv got a motorised dish 42 east to 30 west iv done all that im up and running the only what I cant set up is bull sat regards deltec I can put cams in satellite list lcd4 im only stuck now on how to do bull sat thanks again for all ur help

 

[deltec]

how come I can get bull sat with my technomate 5402 with my cline and I can not open the channels with my duo2 with my cline is there a way I can open 39 east bull sat with my duo 2 and cline if so could boday explain how I do this please thank u very much for all the help so far regards deltec great forum

 

[Ten Below]

The CCcam in the TM5402 is actually a patched version of mgcamd, to clear these in our duo2 use Mgcamd, Oscam, ymod or doscam as client.

 

[deltec]

thank u again :b0227:

 

[rumpole]

like yourself i have never found out how to add a c-line
on a mgcamd config file to get these channels open even
as you say a patched non linux box opens the channels and
if anyone can say which works and how to set it up that would
be very helpfull to me

 

[deltec]

could some one how u do the above please regards deltec

 

[Ten Below]

could some one how u do the above please regards deltec

In the mg_cfg the only lines you should need to change from the default values are these.

# network mode, use summ for several clients
# 00 no network (default)
# 01 newcamd netclient
# 02 radegast netclient
# 04 camd3 netclient
# 08 gbox netclient
# 32 cccamd netclient, card list saved as /tmp/cccamd.info
# (ECM only, supported server version up to 2.1.1, later not work)
G: { 32 }

# box type
# 00 autodetect, change only if you think wrong type detected.
# 01 dbox2
# 02 dreambox
# 03 triple-dragon
# 04 relook
# 05 openbox
# 06 dreambox/mips
# 08 stapi/kathrein
# 09 stapi/ipbox
# 11 stapi/openbox
B: { 06 }

Paste you sealion into the file cccamd.list if you find it is named cccamd.list.example then rename that file removing the .example from the end.

 

[deltec]

don't understand mate

 

[Ten Below]

don't understand mate

What image are you using deltec?

 

[deltec]

the latest black hole image

 

[Ten Below]

Ok install this is you don't already have mgcamd installed, once done you will find the files to edit in the /usr/keys/ directory.
View attachment mgcamd-1.3.8_blackhole2_all.ipk

 

[deltec]

still stuck with this

 

[Banny]

You connect to your Duo2 by FTP, browse to the folder - /usr/keys/ in that folder you should find a file called cccamd.list, open/edit it put in your peers sealions (**Sounds like**) details and save the file. You then need to go to your CAMS section make sure MGCAMD is active, it shouldn't require the cam or box to be restarted but you could for good measure, or if making this change doesnt trigger the channels you are referring to to clear.

-----
Im putting this on your post, but offer it advice to all members -

Id suggest building your self a set of reference sheets/files/folders of the steps you took to resolve issues or get new features working, this way should you change image to a new/different version in the future, also means you have the config files, addons and the information to hand and makes the task easier the second time round. With time and patience, all the jargon, terms and files you need to amend will be an easier task...

It worked for me, and if I can do it I am sure you can

 

[deltec]

ill give it a go

 

[deltec]

still stuck

 

[deltec]

whats sounds like mean mate

 

[deltec]

still having problems so I look in my dcc first

 

[Banny]

Its no good saying still stuck, what is your problem? What have you done to try to fix the problem? What happend?

If you provide us with information we may be able to help, but your not giving us much to go off. How did you manage to do this on your technomate?

The setup and configurations are practically the same. With all due respect, you have been asking how to do things, that if your intending to be a hobbyist, should not cause you a headache for long.

Short version - We need you to explain how far you have got, is this even your local or you using a motorised dish etc etc

 

[deltec]

never did it with my technomate resever is there a tutorial on it please ill start from scratch

 

[Banny]

http://vuplus-images.co.uk/index.php?threads/setting-up-openatv-for-s-y-and-Vermin.2603/

Try following this and changing the sat for the one you want, and is this your local, motorised or otherwise?

If you can't tell us your setup and issue, we can't answer you.
----

We are not going to write a step by step guide specific to your needs alone, these things take time, your response are one sentence at best. Everyone is making a massive effort to help, and understand your issues, but you need to help yourself too....

It also seems you are trying to many different things at once, set yourself a target get there, understand how you got there.... You can also find all the answers to transfer from your Technomate.
-----------------

The more you try to help yourself the more other forum members will endeavor to help you.

 

[deltec]

iv got a motorised dish 42 east to 30 west iv done all that im up and running the only what I cant set up is bull sat regards deltec I can put cams in satellite list lcd4 im only stuck now on how to do bull sat thanks again for all ur help