Custom / Unofficial Build OpenPLi (master-next) custom build discussion thread

[Ten Below]

Here is a freshly built version, i will update post #1 if you have better luck with it.

 

[MatMusalen]

Hello friends. I have finally been able to install the image of the last post of OpenPli 5 in my Vu + SoloSE. It is connected to an antenna of 80 cm equipped with engine Stab HH120. I connect with the DCC 2.96 FTP software and administer programs with DogSetting (he has always done very well).
Charging from USB does not give problems or configuration. The cam 2.2.1 is what I do better. The plugin loaded without problems, including KODI (which must then be set). However the problem has arisen me that once tuned several satellites, to download the DogSetting, make bouquets and reload, the deco does not tune the channel. The shows on screen, but not the tune. If retuning again, respects the bouquets and as if the tune well. The same happens if you load another list of programs to be retuning back to the satellites. I have not found other problems and I think it works fine, except as indicated for the channel lists. I hope my experience helps other forum members and thank you very much to the authors of this firmware.
(sorry for my english....)

 

[Ten Below]

Hello friends. I have finally been able to install the image of the last post of OpenPli 5 in my Vu + SoloSE. It is connected to an antenna of 80 cm equipped with engine Stab HH120. I connect with the DCC 2.96 FTP software and administer programs with DogSetting (he has always done very well).
Charging from USB does not give problems or configuration. The cam 2.2.1 is what I do better. The plugin loaded without problems, including KODI (which must then be set). However the problem has arisen me that once tuned several satellites, to download the DogSetting, make bouquets and reload, the deco does not tune the channel. The shows on screen, but not the tune. If retuning again, respects the bouquets and as if the tune well. The same happens if you load another list of programs to be retuning back to the satellites. I have not found other problems and I think it works fine, except as indicated for the channel lists. I hope my experience helps other forum members and thank you very much to the authors of this firmware.
(sorry for my english....)

Thanks for your feedback MatMusalen, can you confirm kodi is now working for the SoloSE with the version attached tp post #41?
I have not tried the DogSettings Editor but can say there are no problems using E-channelizer so may be worth your time trying this.

 

[MatMusalen]

Yes, Kodi is now working with this last versión.
Also would indicate that I must to retune channels when switching skin.
We go to see E-channelizer.
Thanks

 

[G_ogi]

I can also confirm that Kodi is working on SoloSE, with this release. :dancehappy:

But i have probs with locking on channels. I can only watch, auto or manual scanned channels.
If i transfer or install my preferred bouquets, i get error.
I have multiswitch 1.1 with 4 sat's. I have on all sats signals, tested with SignalFinder.

 

[MatMusalen]

Hello Friends :Hi2:.
Indeed any eventuality (eg blocking a streaming Kodi, etc ...) must be retune all channels. By the way, thank you very much for the indication of e-Channelizer. It's a great program and works perfectly. However, despite having all the correct settings saved with the E-Channelizer, although it retype all that good configuration in the deco, the problem is not resolved and it's back to retune.
Greetings to all.

 

[Ten Below]

I can also confirm that Kodi is working on SoloSE, with this release. :dancehappy:

But i have probs with locking on channels. I can only watch, auto or manual scanned channels.
If i transfer or install my preferred bouquets, i get error.
I have multiswitch 1.1 with 4 sat's. I have on all sats signals, tested with SignalFinder.
View attachment 12035 View attachment 12036 View attachment 12037

Hello Friends :Hi2:.
Indeed any eventuality (eg blocking a streaming Kodi, etc ...) must be retune all channels. By the way, thank you very much for the indication of e-Channelizer. It's a great program and works perfectly. However, despite having all the correct settings saved with the E-Channelizer, although it retype all that good configuration in the deco, the problem is not resolved and it's back to retune.
Greetings to all.

Thankyou both for the time you have taken to test & more importantly the feedback given, this is exactly the reason we do not have official OpenPLi 5.0 yet & i will now report your tests & to those working on the image then build again once this is resolved, i have no idea how to fix this but the info you have wil go a long way towards solving problems.

Solo4K build added @ post #1
Once again i /we have no way of testing this so please give feedback no matter how irrelevant you think it is.

 

[pecha2k]

seems not to work on vu+ solo se 2, not flash

 

[FrenchSatReceiver]

Hi

@Ten Below my Solo4k arrived today Dish not being delivered till about 29th August once installed and set up ready for first go if you or another one of the guys can help me get set up with everything for this build. I can do some testing for Solo4k if that would be of any help thank you

 

[imsohappy]

openpli-enigma2-5-vusolo4k
been having a go at putting softcams on
crashes box or just don't install ? oscam-11272
But i shall keep going

 

[Ten Below]

openpli-enigma2-5-vusolo4k
been having a go at putting softcams on
crashes box or just don't install ? oscam-11272
But i shall keep going

I have just built this with the latest oscam see how you get on with it, install from telnet.

Please, Log in or Register to view codes content!

 

[imsohappy]

I have just built this with the latest oscam see how you get on with it, install from telnet.

Please, Log in or Register to view codes content!

No joy there Ten ?
also can't change date and time
every time i reboot or restart enigma
I get Thursday the 1st of January 1970
I,v reflashed 5 times ?

 

[Ten Below]

No joy there Ten ?
also can't change date and time
every time i reboot or restart enigma
I get Thursday the 1st of January 1970
I,v reflashed 5 times ?

Ok this is the first feeback ive had for the solo4k so will have a look at it through the week & build again, thanks for taking the time to try.

 

[imsohappy]

Ok this is the first feeback ive had for the solo4k so will have a look at it through the week & build again, thanks for taking the time to try.

Just to let you know
No probs with image on my duo2

 

[ricki]

Sorry to say download of cams doesn t work green screan.
Solo4K build

 

[Ten Below]

Sorry to say download of cams doesn t work green screan.
Solo4K build

Thanks i did not find time to try building again this week but will try asap ricki.

 

[ricki]

I only did test on Pli.

 

[jan-Egil]

Are this bild based on gcc 6.1?

 

[Ten Below]

Are this bild based on gcc 6.1?

No these were built using only the default options for Pli next-master & mx3L's meta-vuplus layer.

 

[jan-Egil]

i get no ending spinner error, have uploadet debug log

 

[Ten Below]

Here is a freshly built version, i will update post #1 if you have better luck with it.

 

[MatMusalen]

Hello friends. I have finally been able to install the image of the last post of OpenPli 5 in my Vu + SoloSE. It is connected to an antenna of 80 cm equipped with engine Stab HH120. I connect with the DCC 2.96 FTP software and administer programs with DogSetting (he has always done very well).
Charging from USB does not give problems or configuration. The cam 2.2.1 is what I do better. The plugin loaded without problems, including KODI (which must then be set). However the problem has arisen me that once tuned several satellites, to download the DogSetting, make bouquets and reload, the deco does not tune the channel. The shows on screen, but not the tune. If retuning again, respects the bouquets and as if the tune well. The same happens if you load another list of programs to be retuning back to the satellites. I have not found other problems and I think it works fine, except as indicated for the channel lists. I hope my experience helps other forum members and thank you very much to the authors of this firmware.
(sorry for my english....)

 

[Ten Below]

Hello friends. I have finally been able to install the image of the last post of OpenPli 5 in my Vu + SoloSE. It is connected to an antenna of 80 cm equipped with engine Stab HH120. I connect with the DCC 2.96 FTP software and administer programs with DogSetting (he has always done very well).
Charging from USB does not give problems or configuration. The cam 2.2.1 is what I do better. The plugin loaded without problems, including KODI (which must then be set). However the problem has arisen me that once tuned several satellites, to download the DogSetting, make bouquets and reload, the deco does not tune the channel. The shows on screen, but not the tune. If retuning again, respects the bouquets and as if the tune well. The same happens if you load another list of programs to be retuning back to the satellites. I have not found other problems and I think it works fine, except as indicated for the channel lists. I hope my experience helps other forum members and thank you very much to the authors of this firmware.
(sorry for my english....)

Thanks for your feedback MatMusalen, can you confirm kodi is now working for the SoloSE with the version attached tp post #41?
I have not tried the DogSettings Editor but can say there are no problems using E-channelizer so may be worth your time trying this.

 

[MatMusalen]

Yes, Kodi is now working with this last versión.
Also would indicate that I must to retune channels when switching skin.
We go to see E-channelizer.
Thanks

 

[G_ogi]

I can also confirm that Kodi is working on SoloSE, with this release. :dancehappy:

But i have probs with locking on channels. I can only watch, auto or manual scanned channels.
If i transfer or install my preferred bouquets, i get error.
I have multiswitch 1.1 with 4 sat's. I have on all sats signals, tested with SignalFinder.

 

[MatMusalen]

Hello Friends :Hi2:.
Indeed any eventuality (eg blocking a streaming Kodi, etc ...) must be retune all channels. By the way, thank you very much for the indication of e-Channelizer. It's a great program and works perfectly. However, despite having all the correct settings saved with the E-Channelizer, although it retype all that good configuration in the deco, the problem is not resolved and it's back to retune.
Greetings to all.

 

[Ten Below]

I can also confirm that Kodi is working on SoloSE, with this release. :dancehappy:

But i have probs with locking on channels. I can only watch, auto or manual scanned channels.
If i transfer or install my preferred bouquets, i get error.
I have multiswitch 1.1 with 4 sat's. I have on all sats signals, tested with SignalFinder.
View attachment 12035 View attachment 12036 View attachment 12037

Hello Friends :Hi2:.
Indeed any eventuality (eg blocking a streaming Kodi, etc ...) must be retune all channels. By the way, thank you very much for the indication of e-Channelizer. It's a great program and works perfectly. However, despite having all the correct settings saved with the E-Channelizer, although it retype all that good configuration in the deco, the problem is not resolved and it's back to retune.
Greetings to all.

Thankyou both for the time you have taken to test & more importantly the feedback given, this is exactly the reason we do not have official OpenPLi 5.0 yet & i will now report your tests & to those working on the image then build again once this is resolved, i have no idea how to fix this but the info you have wil go a long way towards solving problems.

Solo4K build added @ post #1
Once again i /we have no way of testing this so please give feedback no matter how irrelevant you think it is.

 

[pecha2k]

seems not to work on vu+ solo se 2, not flash

 

[FrenchSatReceiver]

Hi

@Ten Below my Solo4k arrived today Dish not being delivered till about 29th August once installed and set up ready for first go if you or another one of the guys can help me get set up with everything for this build. I can do some testing for Solo4k if that would be of any help thank you

 

[imsohappy]

openpli-enigma2-5-vusolo4k
been having a go at putting softcams on
crashes box or just don't install ? oscam-11272
But i shall keep going

 

[Ten Below]

openpli-enigma2-5-vusolo4k
been having a go at putting softcams on
crashes box or just don't install ? oscam-11272
But i shall keep going

I have just built this with the latest oscam see how you get on with it, install from telnet.

Please, Log in or Register to view codes content!

 

[imsohappy]

I have just built this with the latest oscam see how you get on with it, install from telnet.

Please, Log in or Register to view codes content!

No joy there Ten ?
also can't change date and time
every time i reboot or restart enigma
I get Thursday the 1st of January 1970
I,v reflashed 5 times ?

 

[Ten Below]

No joy there Ten ?
also can't change date and time
every time i reboot or restart enigma
I get Thursday the 1st of January 1970
I,v reflashed 5 times ?

Ok this is the first feeback ive had for the solo4k so will have a look at it through the week & build again, thanks for taking the time to try.

 

[imsohappy]

Ok this is the first feeback ive had for the solo4k so will have a look at it through the week & build again, thanks for taking the time to try.

Just to let you know
No probs with image on my duo2

 

[ricki]

Sorry to say download of cams doesn t work green screan.
Solo4K build

 

[Ten Below]

Sorry to say download of cams doesn t work green screan.
Solo4K build

Thanks i did not find time to try building again this week but will try asap ricki.

 

[ricki]

I only did test on Pli.

 

[jan-Egil]

Are this bild based on gcc 6.1?

 

[Ten Below]

Are this bild based on gcc 6.1?

No these were built using only the default options for Pli next-master & mx3L's meta-vuplus layer.

 

[jan-Egil]

i get no ending spinner error, have uploadet debug log