Hardware Support VU+ Solo SE stuck in starting

[Kimppa]

Hi,my VU+ is stuck in "starting enigma2" and it was the same with my old Black Hole image,what can I do to fix this issue?
I did not do anything with it like changing images or downloaded any FW,it just stuck suddenly and now I have tried a newer image and it is the same,also tried a old one from 2015 image and it´s the same problem saying "starting guide"

 

[Jackru]

Try first to install the factory image and then try again your Black Hole image and see what it say's

 

[Kimppa]

Where can I find the factory image?

 

[Jackru]

Here the link

Please, Log in or Register to view URLs content!

 

[Kimppa]

Okay,now I installed the Vu+ image and it stuck on loading.........?

 

[Jackru]

did you tryed also a different usb stick to flash your box ?

 

[Kimppa]

No I have not because it starts up like normal,asking language and HDMI and all other starting questions. But I can try another just in case.

 

[Jackru]

But if you can choose between languages and HDMI, tunersetup etc this is your main setup for your box afhter flashing a image so the box startup normal...... what is the problem then ?

 

[Kimppa]

This is the only thing I see.....starting enigma2......

Or the older image "starting guide" ......and now with the Vu+ image "loading....."

Perhaps it just easier to buy a new reciever.......

 

[calypso]

Are you using an original image from Blackhole or a backup Blackhole Image?

 

[Kimppa]

I tried the images that is attached below but if it is an original or a backup I don´t know.

 

[Kimppa]

And this also.......

 

[calypso]

The Blackhole_3.0.9 seems to be ok. but your attachment shows 3.0.8. The 2.1.6 is too outdated.
The reason why I asked was because upon a BH backup., sometimes the kernel_cfe_auto.bin file would need to be substituted with the one contained in the raw image before installation of image. But in this case it seems to be ok.
And as Jackru has already observed, if you're reaching the Setup screen, it means that the Image has already been loaded and ready to be setup.
I would first reflash the 3.0.9 version with a different usb stick or try a completely different image such as OpenVix and see what happens.
Maybe all you need is to properly setup your Image.
Good luck m8.

 

[Kimppa]

I´m sorry I just searched for a pricture to show the screens image......I´ll try one more time....and make the channel search even if the screen shows "starting enigma2"

 

[Kimppa]

Hi,my VU+ is stuck in "starting enigma2" and it was the same with my old Black Hole image,what can I do to fix this issue?
I did not do anything with it like changing images or downloaded any FW,it just stuck suddenly and now I have tried a newer image and it is the same,also tried a old one from 2015 image and it´s the same problem saying "starting guide"

 

[Jackru]

Try first to install the factory image and then try again your Black Hole image and see what it say's

 

[Kimppa]

Where can I find the factory image?

 

[Jackru]

Here the link

Please, Log in or Register to view URLs content!

 

[Kimppa]

Okay,now I installed the Vu+ image and it stuck on loading.........?

 

[Jackru]

did you tryed also a different usb stick to flash your box ?

 

[Kimppa]

No I have not because it starts up like normal,asking language and HDMI and all other starting questions. But I can try another just in case.

 

[Jackru]

But if you can choose between languages and HDMI, tunersetup etc this is your main setup for your box afhter flashing a image so the box startup normal...... what is the problem then ?

 

[Kimppa]

This is the only thing I see.....starting enigma2......

Or the older image "starting guide" ......and now with the Vu+ image "loading....."

Perhaps it just easier to buy a new reciever.......

 

[calypso]

Are you using an original image from Blackhole or a backup Blackhole Image?

 

[Kimppa]

I tried the images that is attached below but if it is an original or a backup I don´t know.

 

[Kimppa]

And this also.......

 

[calypso]

The Blackhole_3.0.9 seems to be ok. but your attachment shows 3.0.8. The 2.1.6 is too outdated.
The reason why I asked was because upon a BH backup., sometimes the kernel_cfe_auto.bin file would need to be substituted with the one contained in the raw image before installation of image. But in this case it seems to be ok.
And as Jackru has already observed, if you're reaching the Setup screen, it means that the Image has already been loaded and ready to be setup.
I would first reflash the 3.0.9 version with a different usb stick or try a completely different image such as OpenVix and see what happens.
Maybe all you need is to properly setup your Image.
Good luck m8.

 

[Kimppa]

I´m sorry I just searched for a pricture to show the screens image......I´ll try one more time....and make the channel search even if the screen shows "starting enigma2"